Ham Radio--Collins, Amps, Antennas, Keys & More!

Please click on the "Auctioneer's Website" link above, for the full catalog, registration, and bidding.

Another great auction, is on the block! Included is a beautiful, rare, National NCX-1000 transceiver, along with an Alpha 91B amp, Yaesu FT-710 transceiver, Elecraft K3/100 transceiver and P3 Panadapter, just to name a few items. We'll also be featuring a nice selection of Collins gear and parts as well as numerous antennas, VHF/UHF amplifiers and CW keys. For test equipment we have a very nice, working, Fluke 5700A Calibrator with a 5725A amplifier. This is the calibrator that is still in use by many calibration labs around the country. Truly a very sophisticated and desirable unit. Continuing on with test gear, there are two TV-7D/U tube testers available! As always we have a great selection of accessories and other related items. 

CATALOG TEXT BELOW:
1 - PAYMENT! At the conclusion of this auction, the credit card you used to register with will automatically be charged for your purchases. International bidders, please see last paragraph below. A PAID invoice will be emailed to you. Please be sure that the card you used to register has sufficient funds/credit limit available. If you do not receive this email by Friday morning, please check your SPAM folder. You can always email or call the auction company and have us resend the email to you. INTERNATIONAL BIDDERS, unless you are an established customer, a bank wire transfer will be required for all purchases over $100 USD. Please contact auction company for wire transfer information.

1a - BIDDING! Bidding is really simple, particularly if you've bid in an online auction before, but here's a quick rundown on some features that may be unfamiliar: Each lot in the auction is scheduled to close approximately 20 seconds apart. For example, Lot 1 is scheduled to close at 7:00.00 pm central time. Lot 2 is scheduled to close at 7:00:20, Lot 3 is scheduled to close at 7:00:40, Lot 4 is scheduled to close at 7:01:00. Soft Close--- The auction software has a "soft close" feature so that if a lot is bid on in the final three minutes before that particular lot is scheduled to close, that lot extends for another three minutes. For example, say Lot 10 has one minute left before it closes and a bid is placed on it: Lot 10's time will extend to four minutes. Then if Lot 10 ticks back down to two minutes remaining and another bid is placed, then Lot 10 will extend to five minutes. As long as active bidding is occurring in that final three minute window, it will keep extending that lot's time. This does not affect any other lots in the auction, just that particular lot. This is the easiest way to emulate "live" auction bidding, and a very common practice in online auctions (not eBay). High bids and maximum bids--- Bidders can place maximum bids which remain secret; the system will only bid up to the competitive bids and show that number as the high bid. For example, if your maximum bid is $100 and the next highest bidder's maximum bid is $40, then you would be the high bidder at $41 (based on the bid increment table). If bids go past your maximum, you'll be notified by email that you've been outbid and can then bid again if you choose. If two bidders happen to have the same maximum bid, then the first bidder at that value is shown as the high bidder.

1b - PREVIEW/PICKUP! Previews and pickup will be located at: 404 NE 41st. St., BLDG 2 Kansas City, MO 64116 (commercial building behind home; look for the 50 ft. tower) Preview Date: Saturday, 10/12 from 9AM - Noon CT, by Appointment Only. Local Pickup Date: Pickup is scheduled for Saturday, 10/19 from Noon - 3PM CT.

1c - SHIPPING! IF SHIPPING IS REQUIRED, WE ADVISE YOU TO CONTACT OUR SHIPPER OR THE AUCTION COMPANY FOR A QUOTE PRIOR TO BIDDING. WEIGHTS AND DIMENSIONS OF EACH LOT ARE INCLUDED IN THE ITEM DESCRIPTION. WE DO NOT SET SHIPPING/PACKING CHARGES. THEIR INFORMATION AND OTHER RELATED INFO CAN BE FOUND AT THE LINK BELOW. PLEASE COPY AND PASTE IT INTO YOUR BROWER TO VIEW. https://www.schulmanauction.com/vintage-electronics/auction-shipping/

1d - EQUIPMENT TESTING! When possible, we do our best to test the equipment we sell so that you will know exactly what you are bidding on. That being said, we perform basic tests such as overall power consumption, receiver sensitivity, transmitter power output, etc. Depending on what it is we’re selling, other tests might be warranted. If there is a certain type of test you’d like performed on a particular lot, just let us know and we’ll do our best to take care of you. Please note that we do not usually go through every single function on a particular piece of gear (in some cases, that would take a considerable amount of time) but rather the functions that will tell us (and you) whether or not the piece of equipment your interested in, is in basic working order. Does it transmit? Does is receive? Does that piece of test gear you’re wanting to bid on do what it is supposed to do? All this with supporting data and photos when appropriate. For more information and specifics about our test bench, please cut and paste the following link into your browser: http://www.schulmanauction.com/vintage-electronics/test-bench-equip-testing/

2 - ETO Alpha 91B HF Linear Amplifier, 220V ETO Alpha 91B HF Linear Amplifier. Very nice looking amplifier, with Peter Dahl transformer, 2, GU-74B output tubes, and user manual. Idle current is 200 ma, and plate voltage is 2800v. There is some fan noise, but some lubrication should take care of that. Very good display. Power output with about 60W of drive, is as follows: 160M, 1500W 80M, 1200W 40M, 1300W 20M, 1300W 15M, 1200W 10M, 1500W PLEASE NOTE: The power supply will be shipped separately, if shipping is required. SN 9517 10043 17x16x8, 66 lbs

3 - National NCX-1000 Transceiver This vintage NCX-1000 HF transceiver, produced by the National Radio Company, is a highly sought-after piece of amateur radio equipment. One of the most beautiful radios from National, and this one doesn't disappoint. Hardly a scratch on the rig, and the chrome is as close to perfect as you can get. Unit comes with dust cover, manual and original box with packing materials. This is a one owner radio. National only made less than 400 of these sets, so they are quite rare and hard to come by, especially in this condition. This is one of the later one's, SN 263. All functions work, and there is no crystal calibrator installed. Power consumption is 120W at 117VAC at idle. All this being said, the radio itself will need an alignment and a cleaning of switches/controls. RX sensitivity is 5.0 to 20.0 uv depending on band. TX power output is as follows: 80M - 32W, 40M - 104W, 20M - 205W, 15M - 92W and 10M - 45W. Please note, it is our opinion that since the bands with the most output had ample screen grid current, and the ones that had the least output, had little to no screen grid current there might be a driver issue as opposed to a weak tube. Also, this set was designed with no provisions for protecting the PA tube. i.e., maximum screen grid current protection and power on HV delay to protect the tube. (if you're bidding on this unit, you probably already know this, but we wanted to mention it anyway) SN 263 18x16x9, 55 lbs

4 - Fluke 5700A Calibrator + 5725A Amplifier Fluke 5700A Multifunction Calibrator, paired with a Fluke 5725A Amplifier. The Fluke 5700A is known for its high-precision calibration capabilities, ideal for calibrating digital multimeters and other critical electrical measurement devices. It delivers highly accurate voltage, current, resistance, and frequency outputs, making it indispensable for calibration labs, manufacturing, and quality assurance environments. The Fluke 5725A Amplifier, included with this unit, extends the current output range of the 5700A, making it suitable for applications that require higher current calibrations. This combination is a powerhouse for users demanding superior performance, precision, and reliability in their calibration tasks. The front panel features a user-friendly interface with numerical keypads, function buttons, and a bright, easy-to-read display. Multiple output and sense ports provide flexibility in setting up calibration procedures. Both units are in overall very good cosmetic condition, as shown. Includes cable to connect amp to calibrator, as well as a sense/output cable for the calibrator, other various patch cables, and a Fluke 50 ohm, DC - 100 MHz feed through termination. Also includes 5700A Operator Reference Guide. These units have the original calibration stickers from Fluke, back in the 90's. Both the calibrator and the amp passed all basic and extensive self tests, and using our Fluke 45 bench meter, we were able to successfully test the unit and find it very good working condition, when testing resistance, voltage and amperage readings. (see last few photos). Some cal labs that we called can't calibrate this unit, as it is the exact unit they use for their calibrations, so it would be a 1 to 1 cal. They suggested sending it back into Fluke for a calibration, if needed, by the new owner. 25x17x7 calibrator; 62 lbs. 25x17x6 amp; 70 lbs.

5 - Yaesu FT-710 Xcvr + SP-40 Speaker Yaesu FT-710 HF/50 MHz Transceiver + SP-40 Speaker in very good to excellent cosmetic as well as working condition. Very lightly used. Includes docs, mic, DC power cord and original box, as shown. TX power output ranges from 100W to 95W from 160M to 10M, and 90W on 6M. RX sensitivity is better than 0.1 uv on all bands. SN 3I150477 7x12x17 box, 16 lbs total

6 - Elecraft K3/100 Transceiver Elecraft K3/100 Transceiver in overall very good cosmetic condition. Includes KPA3, KIO3 and KXV3 options. Display is bright and sharp, and RX sensitivity is 0.1 uv across all bands. TX power output range from 110W on 160M to 100W on 6M. Very nice rig! SN 2306 12x11x5, 9 lbs

7 - Elecraft P3 Panadapter & Coupler/TX Sensor Elecraft P3 Panadapter with 160M through 6M, 2kW, directional coupler/TX sensor, as shown. Both units are in good working condition, as you can see from the photos (second photo is w/o the coupler in use, and the third photo is with the coupler). SN 354 5x6x11, 5 lbs

8 - Kenwood TS-2000 HF/VHF/UHF Transceiver Kenwood TS-2000 HF/VHF/UHF Transceiver in overall very good cosmetic condition. Includes hand mic, DC power cord, and documentation, as shown. Display is bright and sharp, all controls work well, as does the internal tuner. This rig has been reset to factory defaults. RX sensitivity ranges from 0.1 to 0.2 uv on all bands. TX power output ranges from 95W to 85W on 160M through 10M. 25W on 6M, 90W on 2M and 50W on 440 MHz. SN B2300029 15x11x4, 17 lbs

9 - Tokyo Hy-Power HL-45B Power Amplifier Tokyo Hy-Power HL-45B Power Amplifier. This amplifier does appear to be new old stock, or very lightly used. See link to product brochure, above. It works very well, 5W in, output ranges from 55W out on 160M to 45W out on 6M. Note: This is amp was designed to auto band switch with the Yaesu FT-817 QRP rig, but will work with other rigs as well, you will just have to switch bands manually. 4x9x11, 5 lbs

10 - Alpha 99 Linear Amplifier, w/o tubes or xfrmr Alpha 99 Linear Amplifier. This amp DOES NOT INCLUDE GU-74B tubes, or a power transformer (it came into us this way). Cosmetically, external surfaces look good, however, as you can see from some of the internal photos, there is some corrosion evident in certain areas. There was also a separate tap with a terminal block added for the filament connection, as shown. That being said, we were able to test this unit with the Alpha 91B transformer (they use the same) and a couple of the GU-74B tubes found elsewhere in this auction. Idle current is 220 ma, and plate voltage was 2800-3000V. The results are as follows, with 60W of drive power output ranged from 1500W on 80M to 1000W on 10M, so the amp basically works, just supply the tubes and transformer! The multimeter switch needs some Deoxit, as well. Hammond Mfg., makes the transformers and they run between $400 and $500, and the tubes can be found in this auction, as well as other online venues. This amp will also make a nice parts unit, if you are looking for Alpha 99 parts! SN 9999436002 17x16x8, 25 lbs

11 - Collins KWM-2 Transceiver, RE Collins KWM-2 Transceiver, RE. Nice looking radio! RX sensitivity is better than 0.3 uv on all bands and TX power output ranges from 125W on 80M to 87W on 10M. Modulation is good! Very nice addition to your Collins collection. SN 15256 8x15x14, 19 lbs

12 - Collins 32S-3 Transmitter, WE Collins 32S-3 Transmitter, WE, in overall good cosmetic condition. This rig needs the external "P.A. Disable" jumper installed. P.A. grid meter position is intermittent, however, TX power output is as follows: 85W on 80M, 104W on 40M, 101W on 20M, 91W on 15M and 75W on 10M. Modulation is good! SN 11347 15x12x8, 17 lbs

13 - Collins 32S-3 Transmitter, RE Collins 32S-3 Transmitter, RE, in overall good cosmetic condition, as shown. This set will need the external "P.A. Disable" jumper installed. TX power output is as follows: 103W on 80M; 110W on 40M; 90W on 20M; 90W on 15M and 56W on 10M. Modulation is good! SN 102136 15x12x8, 17 lbs

14 - Collins 32S-1 Transmitter, WE Collins 32S-1 Transmitter, WE in overall good cosmetic condition, as shown. TX power output is 108W on 80M and 55W on 10M. Modulation is good! NOTE: THERE is NO output on 40/20/15M. SN 10395 15x12x8, 17 lbs

15 - Collins 312B-5 Station Control, RE Collins 312B-5 Station Control, RE in overall good cosmetic condition, as shown. Includes original manual. PLEASE NOTE: This unit does not have an SWR bridge installed. Otherwise, oscillator has good output level, frequency is OK. Phone patch untested. SN 11597, with manual 12x10x8, 6 lbs

16 - Collins 312B-4 Station Control, RE Collins 312B-4 Station Control, RE, in overall good cosmetic condition, as shown. This unit is in good working condition. SN 62823 12x10x8, 6 lbs

17 - Collins 312B-4 Station Control, WE Collins 312B-4 Station Control, WE, in overall good cosmetic condition, as shown. This unit is in good working condition. SN 54633 12x10x8, 6 lbs

18 - Collins 312B-3 Speaker, WE Collins 312B-2 Speaker, WE in good overall cosmetic as well as working condition. SN 2074 12x10x7, 3 lbs

19 - Collins 516F-2 Power Supply Collins 516F-2 Power Supply, RE. Includes rectifier tubes, but they are not shown. Unit is in good cosmetic as well as working condition. SN 60195 12x10x8, 26 lbs

20 - Collins 516F-2 Power Supply, no cabinet/tubes Collins 516F-2 Power Supply, no cabinet or tubes. However, we did test with a set of in-house tubes, and all voltages are present/correct. SN 15305 6x9x8, 27 lbs

21 - Collins 516F-2 Power Supply, RE Collins 516F-2 Power Supply, RE in very good cosmetic condition, as shown. All voltages are present/correct. SN 23896 12x10x8, 26 lbs

22 - Collins 516F-2 Power Supply/Speaker, WE Collins 516F-2 Power Supply/Speaker, WE. In overall good cosmetic as well as working condition. All voltages present/correct. The AC power cord will need to be replaced. SN 254 12x10x8, 26 lbs

23 - Collins 516F-2 Power Supply/Speaker, WE Collins 516F-2 Power Supply/Speaker, WE. In overall good cosmetic condition. Unit does have SS rectifiers, and speaker works well. B+ voltages are roughly 1/2 of correct values, AC ripple is less than 5V, filament voltage is 3+ VAC. SN 14426 12x10x8, 26 lbs

24 - Collins 51S-1A Receiver, 28VDC WE Collins 51S-1A Receiver, WE for parts or restore. No tuning knob, feet and cabinet screws are missing. Cabinet appears to have been repainted poorly. NOTE: This is the 28VDC version. Untested. No serial number on inside ID plate. 8x15x14, 39 lbs

25 - Collins KWM-2 Transceiver, WE Collins KWM-2 Transceiver, WE. In overall good cosmetic condition, as shown. This rig will need some TLC. Audio oscillates when AF gain is 30% or greater; no RX noise heard; no TX exciter drive or power output. SN ID tag has worn off or been removed. 8x15x14, 19 lbs

26 - Collins R-390/URR Receiver Collins R-390/URR Receiver in overall very good cosmetic condition, with top and bottom covers. Unit is in working condition with RX sensitivity ranging from 0.5 uv to 2.0 uv depending on band. Note that the switches and controls are dirty/noisy and will need cleaning or lubrication. Power consumption is 195W at 117VAC. 19x17x10, 85 lbs

27 - Collins R-390A/URR Receiver Collins R-390A/URR Receiver in overall very good cosmetic condition, as shown. With top and bottom covers. Power consumption was higher than normal for this unit, and kept climbing, so we powered it down with no further testing. Suspect filter caps to start with. SN 3688 19x17x10, 85 lbs

28 - President HR2600 10M Transceiver President HR2600 10M Transceiver in overall good cosmetic condition, as shown. RX sensitivity is 0.3 uv or better and TX power output is 10W. SN 35000266 10x8x3, 5 lbs

29 - Icom IC-475A UHF Transceiver Icom IC-475A UHF Transceiver. In overall good cosmeitc condition, however, the display backlight is out on the right side. TX power output is 20W on all modes, and RX sensitivity is 0.2 uv. SN 01066 4x10x10, 14 lbs

30 - V-J 90PL Two Meter Amplifier V-J 90PL Two Meter Amplifier in working condition. 10W input will get approximately 80W+ output. 3 lbs

31 - Trielectric A 2080H Amplifier Trielectric A 2080H Amplifier, 25W of drive produced approximately 70W output. 3 lbs

32 - Trielectric A 2080H Amplifier Trielectric A 2080H Amplifier, 25W of drive produced approximately 70W output. 4 lbs

33 - KLM Electronics PA15-160BL 2M Amplifier KLM Electronics PA15-160BL Amplifier 35 W at 146.5 MHz, 125W output. Switches, relays and lights in working condition. 3x8x8, 5 lbs

34 - Mirage D1010 100 Watt UHF Amplifier Mirage D1010 100 Watt UHF Amplifier in good working condition. 8-10W input produced 90-100W+ output. 3x6x11, 5 lbs

35 - KLM PA 15-110CL UHF Amplifier KLM PA 15-110CL UHF Amplifier in good working conditoin. 4W in and 70W out, and 10W in 110W out. 10x7x3, 5 lbs

36 - PA 23 cm 60W Linear Amplifier PA 23 cm 60W Linear Amplifier, power on (requires 28VDC) but did not test any further due to not having a 23 cm exciter. 4 lbs

37 - Mirage B108 Amplifier Mirage B108 Amplifier in good working condition. 4W in gets about 50W out, 8W is 90-100W output. 3 lbs

38 - Preamp LNA 03-23cm-v.05 Preamp LNA 03-23cm-v.05, as shown. Appears to be unused and works well. 30 dBm gain at 1250 MHz with 10 VDC applied. 1 lb

39 - Flex Radio Flex-1500 Transceiver Flex Radio Flex-1500 Transceiver. Includes software CD and cabling, as shown. We installed the software for this radio from 2010, and it activated the radio as intended. However, RX was very weak, to t the point that no signals on the band could be heard, other than RX noise. We injected a 0.0 dBm signal into the rig, and heard that, however. Also, the max power output of the radio is 10W, which is what was shown in the software display, however, our power meter did not show any power output. Power consumption at 13.8VDC was about .3A in RX and when the radio was keyed, it did jump to .9A. So, we're not exactly sure if this is a software configuration issue or if the radio has issues. Please bid accordingly. 3 lbs

40 - Ameritron ALS-600 amp + 600PS Pwr Sply Ameritron ALS-600 + 600PS Power Supply. In overall good cosmeitc condition, as shown. The power supply for this amp is good, however, the MRF150 finals in the amplifier are shot, and will need to be replaced. Other adjustments may be necessary as well. SN 13109 10x11x6 (amp), 14x11x6 (ps) 47 lbs total

41 - Harris RF-1310 Exciter Harris RF-1310 Exciter, with power cord. Unit powers on. Self Test OK. Some type of output waveform can be seen on scope, but was unable to perform any further testing. 7x19x21, 40 lbs

42 - Johnson Viking Kilowatt Amplifier RF Deck Johnson Viking Kilowatt Amplifier RF Deck, as shown. Tube filaments are good, and tubes will be shipped separately, if shipping is required. No other testing was performed. 15x17x14, 50 lbs

43 - Collins 637T-1 Dipole Antenna, NOS Collins 637T-2 Dipole Antenna, NOS, as shown. With Collins acceptance tags dated to 1988. 6 lbs

44 - Collins 32MS-1C Transceiver Collins 32MS-1C Transceiver, as shown. Not tested. 9x16x22, 50 lbs.

45 - Collins 18S-4 Transmitter Receiver Collins 18S-4 Transmitter Receiver, as shown. Not tested. 8x16x22, 60 lbs.

46 - Collins 4882-SW Mobile Control Collins 4882-SW Mobile Control. Here's something you definitely don't see every day! In good overall condition, untested. 7x10x8, 10 lbs

47 - Six Collins Wafer Switch Sections Six Collins Wafer Switch Sections. See last photo for Collins P/N. 1 lb

48 - Three Collins S-Line VOX Relays, 32S-1/2/3 Three Collins S-Line VOX Relays for 32S-1/2/3. As shown. NOS. See last photo for P/N. 1 lb

49 - Three Collins Antenna Relays, 32S-1/2/3, KWM2A Three Collins Antenna Relays, 32S-1, 2, 3, KWA2A, as shown, NOS. 1 lb

50 - Three Collins Adj. Tuned Input Coils for 30L-1 Three Collins Adj. Tuned Input Coils for 30L-1. NOS. See last photo for P/N. 1 lb

51 - Three Collins Adj. Tuned Input Coils for 30L-1 Three Collins Adj. Tuned Input Coils for 30L-1. NOS. See last photo for P/N. 1 lb

52 - Three Collins Adj. Tuned Input Coils for 30L-1 Collins Adj. Tuned Input Coils for 30L-1. NOS. See last photo for P/N. 1 lb

53 - Three Collins Adj. Tuned Input Coils for 30L-1 Three Collins Adj. Tuned Input Coils for 30L-1. NOS. See last photo for P/N. 1 lb

54 - Five Collins S-13-7 Switches for KWM2-A Five Collins S-13-7 Switches for KWM2-A. NOS. See last photo for P/N. 1 lb

55 - Nine Collins Rotary Switches, KWM2 Nine Collins Rotary Switches, KWM-2. NOS. See last photo for P/N. 1 lb

56 - Three Collins K Relays for KWM2-A Three Collins K Relays for KWM2-A. NOS. See last photo for P/N. 1 lb

57 - Two Collins Relays Two Collins Relays, 971-1353-00, NOS. As shown. 1 lb

58 - Six Collins E8-50E Trimmer Capacitors 6 E8-50E Trimmer Capacitors. NOS. See last photo for P/N. Silver dollar for size comparison only, and is not included. 1 lb

59 - Four Emission Switches for Collins KWM2-A Four Emission Switches for Collins KWM2-A, NOS. See last photo for P/N. 259-1076-00 1 lb

60 - Four Collins KWM-2A, 3-Pos. SW Levers Four Collins KWM-2A, 3-Pos. SW Levers, NOS. P/N 259-1014-00. 1 lb

61 - Two Rockwell Collins Radio Frequency Coils Two Rockwell Collins Radio Frequency Coils, 543-8028-002, NOS. 1 lb

62 - Collins Bandswitch Face Plate for a 32S-2 Collins Bandswitch Face Plate for a 32S-2. A couple minor paint chips around the edges, as shown. 1 lb

63 - Three Fan Mounts for Collins KWM-2's Three Fan Mounts for Collins KWM-2s. NOS, as shown. 1 lb

64 - Eico 720 Transmitter Eico 720 Transmitter in overall good cosmetic condition, as shown. This rig will need a bit of work, as we have tried 80/40M crystals with no indication of output. Power consumption is 72W at 117VAC. 6x11x7, 27 lbs

65 - Eico 720 Transmitter Eico 720 Transmitter in overall fair cosmetic condition, with some paint chips/flecks, and missing cabinet screws. This radio will need some TLC as well, as it will not power up. Fuse is good! 6x11x7, 27 lbs

66 - Eico 722 VFO Eico 722 VFO for restoration. There is no output on any band. Power consumption is 17W at 117VAC. 7x9x9, 9 lbs

67 - Eico 730 Modulator Driver Eico 730 Modulator Driver in overall good cosmetic condition with some paint chips, as shown. The unit powered up and current draw was reasonable, but was unable to fully test without a working transmitter. Power consumption in RX/Standby was 50W and in TX was 125W, both at 117VAC. 7x14x9, 19 lbs

68 - Johnson Viking KW Match Box & Directional Coupler Johnson Viking KW Match Box + Directional Coupler in very good cosmetic condition. The only issue is that we found was that 3 of the 4 rubber feet are missing and will need to be replaced. Otherwise, a beautiful addition to your vintage shack! The unit is in good working condition, as well! 12x18x13, 21 lbs

69 - Johnson Viking 122 VFO Johnson Viking 122 VFO in overall fair/good cosmetic condition with some paint chips, as shown. That being said, this unit works well with about 15-30 Vp-p output on all bands. 8x7x7, 5 lbs

70 - Johnson 250-39 T-R Switch Johnson 250-39 T-R Switch in good working condition. 5 lbs

71 - Heathkit DX-60B Transmitter Heathkit DX-60B Transmitter in good cosmetic and working condition. 10 W on 10M to 50W on 80M. 14x11x7, 22 lbs

72 - Heathkit HG-10 VFO Heathkit HG-10 VFO in good cosmetic as well as working condition. 10x10x8, 10 lbs

73 - Heathkit HW-8 Replacement Kits Heathkit HW-8 Replacement Kits, HW-8-TR relay replacement, and HW-8-LM386 audio replacement board, by 3rd Planet Solar/KC9ON. Unused, as shown. 1 lb

74 - Kenwood TS-520 SSB Transceiver Kenwood TS-520 SSB Transceiver. Minor wear and tear to housing, note scratch and stain on the top. All functions work fine. RX sensitivity about 0.5 uv on all bands, TX output ranges from 98W on 80M to 70W on 10M. SN 250302 16x13x7, 34 lbs

75 - Kenwood SM-220 Station Control Kenwood SM-220 Station Control in good cosmetic and working condition. SN 0020132 8x9x14, 11 lbs

76 - Kenwood 599 Twins Transceive Cable Kenwood 599 Twins Transceive Cable. Not easy to find one of these nowadays! 1 lb

77 - Kenwood T-599D Transmitter Kenwood T-599D Transmitter in good overall cosmetic condition, with manual, as shown. This rig blows a fuse when tuning for max output, and, the tuning knob does not appear to be calibrated to actual output. For instance, on 20M, 75W max is where the fuse will blow. So, some adjustments will be necessary. SN 540129 16x11x6, 27 lbs.

78 - Kenwood R-599D Receiver Kenwood R-599D Receiver in overall good cosmetic condition, however, even though RX noise is heard, there is no actual RX. Also, the unit doesn't appear to tune correctly and the controls and switches are intermittent and noisy. 12x11x6, 18 lbs

79 - Yaesu FC-40 Antenna Tuner Yaesu FC-40 Antenna Tuner. Appears unused and in original box. 5x13x15 (box), 8 lbs

80 - Kenwood SP-23 Speaker Kenwood SP-23 Speaker in good cosmetic and working condition. 2 lbs

81 - Icom SP-41 External Speaker NIB Icom SP-41 External Speaker, new in box, good working condition. 6x9x16 (box), 7 lbs

82 - Kenwood SP-230 Speaker Kenwood SP-230 Speaker, tested and in working condition. 6x7x11, 5 lbs

83 - Yaesu YH-55 Headphones Yaesu YH-55 Headphones, tested and in good working condition, mild cosmetic wear. As shown. 2 lbs

84 - Drake MS8 Speaker Drake MS8 Speaker, in good cosmetic and working condition. 2 lbs

85 - Drake FS-4 Synthesizer Drake FS-4 Synthesizer in good working condition. Includes manual. 12x7x4, 6 lbs

86 - Drake AC-4 Power Supply Drake AC-4 Power Supply, all voltages are present. 10x5x5, 17 lbs

87 - Drake AC-4 Power Supply Drake AC-4 Power Supply blows fuse upon power on. No further testing. 10x5x5, 17 lbs

88 - Drake AC-4 Power Supply Drake AC-4 Power Supply will not power on. Fuse is good. For parts/restoration. 10x5x5, 17 lbs

89 - Drake T-4XC Transmitter Drake T-4XC Transmitter, with box and RCA patch cables, as shown. This radio will power on, but it does not tune properly. So, will need some TLC. No audio or TX SN 25928 13x11x6, 14 lbs

90 - Drake R-4C Receiver Drake R-4C Receiver, with box and manual, in good overall cosmetic condition, as shown. RX sensitivity is quite low, and ranges from 1.0 to 14.0 uv, depending on band. An alignment could probably help. SN 24589 15x11x6, 16 lbs

91 - Drake T-4XB Transmitter Drake T-4XB Transmitter with a set of spare tubes and manuals. We tried both sets of tubes in this rig, filaments light, but there is no TX power output. So some troubleshooting will be needed. Otherwise, a nice looking radio! SN 13973 12x11x6, 15 lbs

92 - Drake R-4B Receiver Drake R-4B Receiver in overall good cosmetic condition, with manual, as shown. RX sensitivity ranges from 6.0 to 10.0 uv depending on band, so an alignment might be needed. SN 12865 12x11x6, 17 lbs

93 - Drake 2-B Receiver Drake 2-B Receiver in overall good to very good cosmetic condition. All functions work, and RX sensitivity is 0.3 uv on all bands. No 10A/10C crystals. Note: switches and controls are dirty/noisy and could use cleaning or lubrication. 12x10x8, 15 lbs

94 - Drake T-4XC Transmitter Drake T-4XC Transmitter in overall good to very good cosmetic condition, with manual, as shown. Unit does power up, however, there is no TX power output. 13x11x6, 14 lbs

95 - Drake 2-LF Converter Drake 2-LF Converter, as shown. Untested. 1 lb

96 - Solartron 4040 Stabilock Communication Test Set Schlumberger Solartron 4040 Stabilock Communication Test Set. Very nice looking and working piece of bench gear! Includes documentation, as shown. All displays and controls work well. Generator output frequency and amplitude was very accurate, and TX power output and frequency was as well (see last few photos). 11x15x18, 50 lbs

97 - TV-7D/U Tube Test Set TV-7D/U Tube Test Set in good overall cosmetic condition, with accessories and reprinted spiral bound reprinted manual, as shown. This unit works well! We tested and compared known good tubes with our recently calibrated TV-7D/U tester at the shop, and the results were almost spot on. Great addition to your test bench! 18x10x7, 22 lbs

98 - TV-7D/U Tube Test Set, for repair TV-7D/U Tube Test Set in overall fair/good cosmetic condition, and includes accessories and reprinted manual, as shown. This test set will not set the line adjust, no meter movement. However, pilot light does illuminate and power consumption is approximately 50W at 117VAC. Being sold for repair. 18x10x7, 22 lbs

99 - Boonton Electronics 92BD RF Millivoltmeter Boonton Electronics 92BD RF Millivoltmeter. In good overall cosmetic condition, as shown. With 91-12F probe. This unit powers up, nice, bright display and meter moves smoothly. We did not have any type of terminator for the probe, so we used a signal source and placed it within a about a 1/2 inch of the probe and the meter deflected properly. Moving the signal source at varying distances from the probe also provided various meter deflections. 6x8x12, 7 lbs

100 - Boonton Electronics 92E RF Millivoltmeter Boonton Electronics 92E RF Millivoltmeter. in overall good cosmetic condition, as shown. With 91-12F probe. This unit powers up, nice, bright display and meter moves smoothly. We did not have any type of terminator for the probe, so we used a signal source and placed it within a about a 1/2 inch of the probe and the meter deflected properly. Moving the signal source at varying distances from the probe also provided various meter deflections. 6x8x12, 7 lbs

101 - HP 8757A Scalar Network Analyzer HP 8757A Scalar Network Analyzer in overall good cosmetic condition. However, no probes are included with this unit. It does pass all self tests. SN 2802A03575 8x18x19, 50 lbs

102 - BIRD 43 Thruline Wattmeter w/4 Slugs BIRD 43 Thruline Wattmeter in good cosmetic as well as working condition, with case, manual, and misc. RF connectors and patch cable, as shown. Includes the following slugs: 250W 2-30 MHz 10W 100-250 MHz 50W 100-250 MHz 100W 200-500 MHz Blank 9x6x4, 6 lbs

103 - 16 BIRD Wattmeter Slugs & Extras 16 BIRD Wattmeter Slugs, and extras! Includes the following: 5W, 25-60 MHz 5W, 400-1000 MHz 25W, 2300-2400 MHz 50W, 400-1000 MHz (x2) 50W, 100-250 MHz 100W, 25-60 MHz 250W, 25-60 MHz 250W, 100-250 MHz 500W, 100-250 MHz (Coaxial Dynamics) 500W, 400-1000 MHz (Coaxial Dynamics) 500W, 2-30 MHz 1000W, 25-60 MHz 1000W, 100-250 MHz 2500W, 2-30 MHz CD Adjustable X-Tractor 43 dB, model 87004 Suhner 4901.19.A Power Divider, 50 ohm, 6 dB, 0.5W, DC-12.4 GHz. 7 lbs

104 - BIRD Wattmeter Line Section BIRD Wattmeter Line Section, in working condition. 1 lb

105 - Ten-Tec HF-VHF SWR/RF Wattmeter Kit Ten-Tec HF-VHF SWR/RF Wattmeter Kit, some assembly required. As shown. 2 lbs

106 - Ameritron AWM-30 Peak Reading SWR/Wattmeter Ameritron AWM-30 Peak Reading SWR/Wattmeter, tested and in good working condition. 2 lbs

107 - Siltronix FS-301 Wattmeter Siltronix FS-301 Wattmeter in good working condition. 2 lbs

108 - MFJ-259B SWR Analyzer MFJ-259B SWR Analyzer in good cosmetic condition, clean battery compartment. In good working condition. 2 lbs

109 - Viking MB-V-A Ant Impedance Matching Network Viking MB-V-A Antenna Impedance Matching Network in good cosmetic condition and works well on all bands. 7x15x13, 16 lbs

110 - LOT of Miscellaneous Elecraft Parts LOT of Miscellaneous Elecraft Parts, as shown. Most appear unopened. 4 lbs

111 - LOT of Miscellaneous Elecraft Parts LOT of Miscellaneous Elecraft Parts, as shown. Most appear unused. 4 lbs

112 - RigExpert AA-54 Antenna Analyzer RigExpert AA-54 Antenna Analyzer in good cosmetic as well as working condition. Clean battery compartment. You will need to supply 2 AA batteries. Includes CD and documentation. 2 lbs

113 - TelePost LP-100A Digital Vector RF Wattmeter TelePost LP-100A Digital Vector RF Wattmeter + LP-100 RF Sensor in good overall cosmetic as well as working condition. Tested against our own LP-100A's and they're right on the money! 4 lbs total

114 - TelePost LP-100A Digital Vector RF Wattmeter TelePost LP-100A Digital Vector RF Wattmeter + LP-100 RF Sensor in good overall cosmetic as well as working condition. Tested against our own LP-100A's and they're right on the money! 4 lbs total

115 - Tektronix K217S Rack Instrument Cart Tektronix K217S Rack Instrument Cart, as shown. In good working condition. PLEASE NOTE: We will not be shipping this item. You can arrange for your shipper to pick this up, or an alternate time for pickup, if you can't make the scheduled time. 38x21x38, 60 lbs

116 - Comet CAT-300 Antenna Tuner Comet CAT-300 Antenna Tuner in good cosmetic as well as working condition. 4x9x10, 6 lbs

117 - SDRSwitch.com Switch Box 0-450 MHz, 100W SDRSwitch.com Switch Box, 0-450MHz 100W RX in RX out SDR Switch in good working condition. See link above to manufacturers website. 2 lbs

118 - LDG KT-100 Autotuner LDG KT-100 Autotuner in good cosmetic as well as working condition. For Kenwood transceivers; a partial list includes: TS-2000, 50, 450, 480SAT (not HX), 570, 590, 850, 870, 990 (and all variants). 2 lbs

119 - Diamond MX-72N Duplexer Diamond MX-72N Duplexer in good working condition. 1 lb

120 - Astron Power Supply RS-10A Astron Power Supply RS-10A. Works well under full load. 5x8x11, 8 lbs

121 - Astron LS-18A, 28VDC Power Supply Astron LS-18A, 28 VDC Power Supply in good working condition, tested well under full load. 6x11x11, 26 lbs

122 - Astron LS-35A, 28VDC Power Supply Astron LS-35A Power Supply, with original box - not shown. Works well, tested at full load. 6x11x11, 24 lbs

123 - Astron RM-50A Rack Mount Power Supply Astron RM-50A Rack Mount Power Supply works well at full load. 6x19x13, 44 lbs

124 - Astron RS-35M Power Supply Astron RS-35M Power Supply in good working condition. Tested OK at full load. 11x11x6, 24 lbs

125 - Heathkit IT-3120 FET/Transistor Tester Heathkit IT-3120 FET/Transistor Tester in good overall cosmetic condition, as shown. Battery compartment is clean, you will need to supply your own batteries and test leads. This unit works well, we tested a few known good transistors with no issues. 5x9x10, 5 lbs

126 - Millen 90651 Grid Dip Meter Millen 90651 Grid Dip Meter, coils A-F. Very nice grid dip meter with case and rare LF coils. This unit is in working condition. 4x7x10, 10 lbs

127 - Sencore TR 139 In-Circuit Transistor Tester Sencore TR 139 Dynamic In-Circuit Transistor Tester. Very good to excellent cosmetic condition, as shown. You will need to supply your own probes. We tested this unit with known good transistors without any issues. In good working condition. 10x8x6, 7 lbs

128 - General Radio W2 Variac General Radio W2 Variac in good working condition. 2 lbs

129 - Drake TV-1000 LP Low Pass Filter Drake TV-1000 LP Low Pass Filter in good working condition. As shown. 1 lb.

130 - "Almost All" Digital Frequency Display "Almost All" Digital Frequency Display in good cosmetic and working condition. 1 lb

131 - B&K 801 Capacitor Analyst B&K 801 Capacitor Analyst in overall good cosmetic condition. The meter does work, but is not at all accurate. Some calibration or other adjustments will be necessary. 6x13x7, 7 lbs.

132 - Two 24 hr. Ham Clocks US Maritime Commission 24h clock by Chelsea Clock Co., and an unmarked 24hr clock, both in working condition but AA batteries not included. Both clocks are plastic. 12" dia, and 10" dia, 2 lbs

133 - AC Line Frequency Monitor AC Line Frequency Monitor in good cosmetic and working condition. 2 lbs

134 - Ameritron RCS-8V Remote Coax Switch + Relay Ameritron RCS-8V Remote Coax Switch + RCS-8V Relay Box. Powers on, all 5 ports switch, LEDs illuminate. 2 lbs

135 - MFJ-1621 Portable Antenna MFJ-1621 Portable Antenna in good cosmetic as well as working condition. 3 lbs

136 - West Mountain Radio RIGblaster Plus West Mountain Radio RIGblaster Plus. In good cosmetic condition. Unit powers up, but no further testing was performed. 1 lb

137 - MFJ-1118 Deluxe High Circuit DC Outlets MFJ-1118 Deluxe High Circuit DC Outlets in good cosmetic and working condition. 2 lbs

138 - West Mountain Radio RIGrunner 4010S DC Outlets West Mountain Radio RIGrunner 4010S DC Outlets in good cosmetic and working condition. 2 lbs

139 - MFJ-1116 DC Power Outlets MFJ-1116 DC Power Outlets in good cosmetic and working condition. 2 lbs

140 - West Mountain Radio RIGrunner 4010S DC Outlets West Mountain Radio RIGrunner 4010S DC Outlets in good cosmetic and working condition. 1 lb

141 - MFJ-1116 Deluxe DC Power Outlets MFJ-1116 Deluxe DC Power Outlets in good cosmetic and working condition. 2 lbs

142 - MFJ-1116 Deluxe DC Power Outlets MFJ-1116 Deluxe DC Power Outlets in good cosmetic and working condition. 2 lbs

143 - West Mountain Radio RIGrunner 4010S West Mountain Radio RIGrunner 4010S in good cosmetic and working condition. 2 lbs

144 - West Mountain Radio RIGrunner 4008 West Mountain Radio RIGrunner 4008 in good cosmetic and working condition. 1 lb

145 - Yaesu SCU-20 PC Connection Cable Yaesu SCU-20 PC Connection Cable, as shown. 1 lb

146 - Kenwood MC-60 Microphone Kenwood MC-60 Microphone in good cosmetic and working condition, as shown. 2 lbs

147 - Heil Proset Headphones Heil Proset Headphones in good cosmetic and working condition. 2 lbs

148 - Heil 8-pin mic adapter for Yaesu Heil 8-pin mic adapter for Yaesu. Previously used with an FT-2000 transceiver. 1 lb

149 - Ten-Tec 705 Electret Microphone Ten-Tec 705 Electret Microphone in working condition - will need a 9V battery. As shown. 1 lb

150 - Astatic D-104 Microphone Astatic D-104 Microphone In good cosmetic and working condition. Amplified base requires 9V battery. 2 lbs

151 - Inrad M628 Microphone Inrad M628 Microphone in new condition, as shown. 3 lbs

152 - Inrad M628 Microphone Inrad M628 Microphone, new condition, with stand, as shown. 3 lbs

153 - Electro-Voice 664 Microphone Electro-Voice 664 Microphone, in beautiful cosmetic and working condition. Includes stand and original box. 4 lbs

154 - Vibroplex Standard Iambic Paddle Vibroplex Standard Iambic Paddle S/N 103523. Unit is in overall very good cosmetic as well as working condition. 2 lbs

155 - Vibroplex Iambic Deluxe Paddle Vibroplex Iambic Deluxe Paddle, in good cosmetic and working condition. 2 lbs

156 - Bencher Iambic Paddle Bencher Iambic Paddle in overall very good cosmetic as well as working condition. 2 lbs

157 - Speed-X Straight Key Speed-X Straight Key, as shown. Works well. 1 lb

158 - T.R. McElroy MAC Radio Telegraph Key T.R. McElroy MAC Radio Telegraph Transmitting Key with metal case. Base with embossed name, ‘James Michael Kane.’ Needs paddle. 3 lbs

159 - Vibroplex Bug + Case, ca. 1944 Vibroplex Bug + Case, ca. 1944 as per the WW7P serial number dating list. 3 lbs

160 - Alpha Delta 2 Coax Switch Alpha Delta 2 Coax Switch in good cosmetic and working condition. 1 lb

161 - Alpha Delta 2 Coax Switch Alpha Delta 2 Coax Switch, in good cosmetic and working condition. 2 lbs

162 - Daiwa CS-401 Coax Switch Daiwa CS-401 Coax Switch in good cosmetic and working condition. 2 lbs

163 - Pair of Unopened R&L Coax Switches Pair of Unopened R&L Coax Switches, in original packages. Nice. 3 lbs

164 - Three Coax Switches Three Coax Switches, MFJ-1702B, Daiwa CS-201, and Heathkit HD-1234. Working order except for the Daiwa which is intermittent. 2 lbs

165 - MFJ-1704 Coax Switch MFJ-1704 Coax Switch in good cosmetic and working condition. 3 lbs

166 - Alpha Delta 2 Coax Switch Alpha Delta 2 Coax Switch in good cosmetic and working condition. 2 lbs

167 - Two MFJ-1702B Antenna Switches Two MFJ-1702B Antenna Switches in good cosmetic and working condition. 2 lbs

168 - Three Heathkit HD-1234 Antenna Switches Three Heathkit HD-1234 Antenna Switches in good working condition. 2 lbs

169 - Four Antenna Switches Four Antenna Switches, all working except for switch shown on the top, middle of the first photo. It does have some open connections. 2 lbs

170 - Jennings UCS Vacuum Variable Capacitor Jennings UCS Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 67 pf to max 300 pf. Max voltage we were able to test at was 600VDC with no leakage. 2 lbs

171 - Jennings UCS Vacuum Variable Capacitor Jennings UCS Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 10 pf to max 300 pf. Max voltage we were able to test at was 600VDC with no leakage. 2 lbs

172 - Jennings UCS-1000 Vacuum Variable Capacitor Jennings UCS-1000 Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 10 pf to max 1000 pf. Max voltage we were able to test at was 600VDC with no leakage. 2 lbs

173 - Jennings UCS-500-15S Vacuum Variable Capacitor Jennings UCS-500-15S Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 15 pf to max 500 pf. Max voltage we were able to test at was 600VDC with no leakage. 2 lbs

174 - Jennings UCS-500/UCSF-500 Variable Capacitor Jennings UCS-500/UCSF-500-0015 Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 11 pf to max 500 pf. Max voltage we were able to test at was 600VDC with no leakage. 3 lbs

175 - Comet CV05C-1000KWF Vacuum Variable Capacitor Comet CV05C-1000KWF/5 Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 10 pf to max 1000 pf. Max voltage we were able to test at was 600VDC with no leakage. 2 lbs

176 - Jennings UCS-375 Vacuum Variable Capacitor Jennings UCS-375 Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 11 pf to max 380 pf. Max voltage we were able to test at was 600VDC with no leakage. 2 lbs

177 - Jennings UCSL-3000 Vacuum Variable Capacitor Jennings UCSL-3000 Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 55 pf to max 2890 pf. Max voltage we were able to test at was 600VDC with no leakage. 3 lbs

178 - Jennings UCSL-500 Vacuum Variable Capacitor Jennings UCSL-500 Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 6 pf to max 500 pf. Max voltage we were able to test at was 600VDC with no leakage. 1 lb

179 - Comet CVUN-1505AC Vacuum Variable Capacitor Comet CVUN-1505AC/4-BEAA Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 80 pf to max 1450 pf. Max voltage we were able to test at was 600VDC with no leakage. 1 lb

180 - Jennings UCSL-500 Vacuum Variable Capacitor Jennings UCSL-500 Vacuum Variable Capacitor. No high-pot testing, but we did use a Sencore LC75 and it tested at min. 10 pf to max 500 pf. Max voltage we were able to test at was 600VDC with no leakage. 2 lbs

181 - Two Kilovac HC-2/S3 Vacuum Relays Two Kilovac HC-2/S3 Vacuum Relays, NOS, as shown. 1 lb

182 - Two Kilovac HC-1/S122 Vacuum Relays Two Kilovac HC-1/S122 Vacuum Relays, used, a shown. 1 lb

183 - Two Kilovac HC-1/S122 Vacuum Relays Two Kilovac HC-1/S122 Vacuum Relays, used, as shown. 1 lb

184 - Two Kilovac HC-3 Vacuum Relays Two Kilovac HC-3 Vacuum Relays, used, as shown. 1 lb

185 - Kilovac + Jennings HC-3 Vacuum Relays Kilovac + Jennings HC-3 Vacuum Relays, used, as shown. 1 lb

186 - Svetlana 4CX800A GU74B Tube Svetlana 4CX800A GU74B Tube, tested at approximately 550W using the Alpha 91B amp found elsewhere in this auction. 2 lbs

187 - Svetlana 4CX800A GU74B Tube Svetlana 4CX800A GU74B Tube, tested at approximately 600-650W using the Alpha 91B amp found elsewhere in this auction. 2 lbs

188 - Svetlana 4CX800A GU74B Tube Svetlana 4CX800A GU74B Tube, tested at approximately 600-650W using the Alpha 91B amp found elsewhere in this auction. 2 lbs

189 - Svetlana 4CX800A GU74B Tube Svetlana 4CX800A GU74B Tube, tested at approximately 600-650W using the Alpha 91B amp found elsewhere in this auction. 2 lbs

190 - Svetlana 4CX800A GU74B Tube Svetlana 4CX800A GU74B Tube, tested at approximately 550W using the Alpha 91B amp found elsewhere in this auction. 2 lbs

191 - CSI Direction Finder Antenna, Unopened CSI Direction Finder Antenna, unopened original package. 4 lbs

192 - Windcamp WA-4 Windom Ant. Balun Windcamp WA-4 WindomAntenna Balun, is missing the antenna wire/connectors, but balun appears unused. 2 lbs

193 - Easy-Tenna Balun Easy-Tenna Balun in very good condition, appears unused. 2 lbs

194 - End Fed Wire Antenna End Fed Wire Antenna, appears unused. As shown. No manufacturer found. 2 lbs

195 - K5WZ 6-80 Meter Horse Fence Dipole K5WZ 6-80 Meter Horse Fence Dipole, omnidirectional, appears entirely unused. Stainless steel, aluminum, PVC 3 lbs

196 - Bilal Isotron 40 Meter Antenna Bilal Isotron 40 Meter Antenna, unused, as shown. 6 lbs

197 - G5RV 80-10 Meter Dipole Antenna G5RV 80-10 Meter Dipole Antenna, as shown. Appears unused. 5 lbs

198 - Two KF4BWG Horse Fence Dipole Antennas Two KF4BWG Horse Fence Dipole Antennas appears unused and in very good condition. 5 lbs

199 - Ameco FD-20 Folded Dipole & Misc. Dipole Ameco FD-20 Folded Dipole Antenna and Misc. Dipole, appears unused. 4 lbs

200 - MyAntennas.com EFHW-8010-2K Antenna MyAntennas.com EFHW-8010-2K End-Fed Half Wave Antenna, appears unused. 4 lbs

201 - G5RV Classic Antenna G5RV Classic Antenna, appears unused. As shown. 5 lbs

202 - Hi-Z Antennas Reversible Beverage Antenna Sys Hi-Z Antennas Reversible Beverage Antenna Sys, as shown. Untested. You will need to supply antenna wire and other materials needed. Please enlarge photos to see model numbers and specs of what you are bidding on. 4 lbs

203 - DX Eng. DXE-TW-2010L-P Antenna + TW-4040 DX Engineering DXE-TW-2010L-P Mono & Multi-Band Vertical Dipole Antenna System + TW-4040 (40M monoband box). This antenna does not appear to have ever been used or assembled.

204 - Ventenna HFp Vertical Antenna, 7-54 MHz Ventenna HFp Vertical Antenna, 7-54 MHz, like new, in original cloth carrier. 7 lbs

205 - CDE Tailtwister Control and T2X Rotor CDE Tailtwister Control and T2X Rotor. Untested, requires custom control cable, 9-pin circular to 8-pin terminal strip. Control: 8x8x4 Rotor 14 inches 23 lbs total

206 - Yaesu G-5500 Dual Controller + Rotor Yaesu G-5500 Elevation-Azimuth Dual Controller + Rotor. Both units are in good working condition. You will need to supply your own rotor cables, the one's shown were cut. 14x6 rotor, 5x6x7 controller, 24 lbs total

207 - Yaesu G-1000DXA Rotor Controller Yaesu G-1000DXA Rotor Controller in good working condition. We tested it in place of our G-1000DXA at the shop. 6x6x8, 7 lbs

208 - Yaesu G-5400B AZ-EL Rotor + Controller Yaesu G-5400B Elevation-Azimuth Rotor + Controller, all units in good working condition. You will need to supply all the appropriate cabling. 13x6x8, 28 lbs

209 - TRA-4 Antenna Rotor + CDE Controller TRA-4 Antenna Rotor + CDE Controller. Controller and rotor do power up, but the gear box is bad, as there is no position feedback, nor do the limits work properly. 28 lbs

210 - Down East Microwave 90-28H6 900MHz Transverter Down East Microwave 90-28H6 900 MHz High Power Transverter, in great shape, but untested. See link above for PDF of docs and schematics. Power cord is not included. 5x7x10, 7 lbs

211 - HP 8640B Signal Generator w/OPT 3 HP 8640B Signal Generator w/OPT3. Nice looking unit, but will need some TLC. Here's what we have found: Time bases and dividers appear to be working, but frequency counter only reads correct frequency on some bands. Nylon gears are cracked and will need replaced, as it is making the adjustment of range knob very stiff. Many switches and controls are dirty/noisy. Attenuator steps properly, but output is 8 dB below actual measurement. SN 2309A21025 5x17x20, 46 lbs

212 - Yaesu FT-1000MP Mark-V Xcvr/FP-29 PS/repair Yaesu FT-1000MP Mark-V Xcvr/FP-29 Power Supply. For restore. No power supply connector on back of supply. We used our bench supply for testing, but were limited to only 30V at 9A. Based on this, TX power output was approximately 50-60W on all bands. RX sensitivity is very weak and will need some work. However, RX noise is heard, and varies with the AF gain contol. SN 2G360019 16x16x7, 33 lbs xcvr. 13x6x4, 8 lbs power supply

213 - Millivac MV-723B RF Millivoltmeter Millivac MV-723B RF Millivoltmeter. In overall good cosmetic condition, as shown. However, we do not have a probe for this unit. It does power up, display is bright, meter moves smoothly and range switches appear to change normally. No further testing performed. 8x8x14, 10 lbs

214 - Icom IC-R7000 Receiver Icom IC-R7000 Receiver in overall good cosmetic condition, as shown. However, the tuning knob/encoder does not work. You can enter frequencies from the keypad. RX sensitivity is 25 uv on VHF and 15 uv on UHF, so the unit will need a bit of TLC. SN 01225 Approx. Weight: 21 lbs. Approx. Dims: 13x13x5

215 - Astron RS-20A Power Supply Astron RS-20A Power Supply for repair. No load voltage is 13.8 VDC, but there is no output with 1.5 A load. 6x7x9, 11 lbs

216 - Icom IC-275A Transceiver, parts/restore Icom IC-275A Transceiver in overall good cosmetic condition, however, their is no display or TX/RX. Being sold for parts or restore. SN 01083 4x10x10, 15 lbs

217 - Racal RA6790/GM R-2174(P)/URR Rcvr for parts Racal RA6790/GM R-2174(P)/URR Rcvr for parts. Heard arcing sound when powered up, no further testing performed. SN 6601 21x20x6, 30 lbs

218 - Racal RA6790/GM R-2174(P)/URR Rcvr for parts Racal RA6790/GM R-2174(P)/URR Rcvr for parts. Powered up, however, both displays are dark. No RX noise heard. SN 4599 21x20x6, 30 lbs

219 - Racal RA6790/GM R-2174(P)/URR Rcvr for parts Racal RA6790/GM R-2174(P)/URR Rcvr for parts. Unit powers up and both diplays show digits, but controls and keypad are inoperable. SN 3265 21x20x6, 30 lbs

220 - Racal RA6772E Manual/Digital HF Receiver Racal RA6772E Manual/Digital HF Receiver. Unit powers on and display flashes briefly. No functionality, no output. No control. For parts. SN 182 9x19x22, 50 lbs

221 - Harris RF-1310 Exciter for parts Harris RF-1310 Exciter for parts, with power cord. Unit powers on, but no display. Fault light is on. No further testing. 7x19x21, 40 lbs

222 - Harris RF-1310 Exciter for parts Harris RF-1310 Exciter for parts, with power cord. Powers up, fault light is on, no display. No further testing performed. 7x19x21, 40 lbs

223 - Harris RF-1310 Exciter for parts Harris RF-1310 Exciter for parts, with power cord. Powers up, fault light is on, no display. No further testing performed. 7x19x21, 40 lbs

224 - Ten-Tec Argosy Transceiver Ten-Tec Argosy Transceiver in good cosmetic condition. Dial won't tune below 2 on the scale, needs repair and some TLC, 80M inoperable, all other bands OK. RX sensitivity less than 0.3uv, TX power 28-30W. S/N 00046 5x10x13, 9 lbs

225 - Advanced Receiver Research SP144VDA Preamp Advanced Receiver Research SP144VDA Preamp in good cosmetic condition. Approximately 25db gain, internal switching relay a bit intermittent, occasionally no gain when turning on. LED switch light is normal. 1 lb

226 - Yaesu CD-41 Battery Charger Base, NIB Yaesu CD-41 Battery Charger Base, basically new in box, in working condition. You will need to supply the appropriate wall wart. 1 lb

227 - Alpha Delta VRC Variable Response Control Alpha Delta VRC Variable Response Control. Good cosmetic condition but no audio output. Bar graph display works. 9x9x7, 9 lbs

228 - Heathkit IM-2215 Portable Digital Multimeter Heathkit IM-2215 Portable Digital Multimeter in good cosmetic condition and with fitted leather case. Battery compartment is clean. LCD screen has a dark center shadow. Switches need cleaning. Indicates AC and DC volts and amps, plus ohms. Needs calibration. 2 lbs

229 - Hitachi 5DEP31 Cathode Ray Tube Hitachi 5DEP31 Cathode Ray Tube. Untested, in very good cosmetic condition. 12-pin octal base. 4 lbs

230 - Microwave Modules 432 MHz Transverter Microwave Modules 432 MHz SSB Transverter, as shown. 28 to 432 MHz works well, however, no output going from 432 to 28 MHz. 3 lbs

231 - Swan 250C Transceiver, VFO, 117XC Power Supply Swan 250C Transceiver, 210 VFO, 117XC Power Supply. Being sold for restoration. Power cable has short at transceiver end. No further testing was performed. SN 10093, 11191, 104701 13x11x16, 18 lbs and 12x7x9, 19 lbs

232 - Heathkit SB-220 Linear Amplifier parts/restore Heathkit SB-220 Linear Amplifier for parts or restoration. This amp has no cabinet, no bottom cover and no tubes. Their is also no plug on the end of the power cord. The band switch is very stiff, and no noticeable "stops" when turning. Being sold for parts or restoration. 8x15x15, 55 lbs

233 - Alinco DJ-580 VHF/UHF HT Transceiver Alinco DJ-580 VHF/UHF HT Transceiver, as shown. RX sensitivity is 0.2 uv on both bands, and TX power output is 0.1W low and 1W high. This is due to the fact that the battery won't hardly hold a charge. You'll need to supply a new battery and a charger. 1 lb

234 - Heathkit T2 Signal Tracer Heathkit T2 Signal Tracer, as shown. Non-polarized AC power plug. Hums in the speaker, switch is intermittent, needs cleaning overall. 8x9x5, 3 lbs

235 - Elecraft KPA500 and KAT500 Tuner by Fred Cady Elecraft KPA500 and KAT500 Tuner by Fred Cady. As shown. 1 lb

236 - Yaesu FT3DT/DE Nifty Mini Manual Yaesu FT3DT/DE Nifty Mini Manual in very good condition. 1 lb

237 - Yaesu FTdx101D & MP Nifty Mini Manual Yaesu FTdx101D & MP Nifty Mini Manual in very good condition. 1 lb